-
Description
Features
- Extruded Tread Surface:
- It is slip-resistant, meaning users are safe to use it in any weather - Adjustable Legs with Swivel Feet:
- Allow for two inches of vertical adjustments
- It adjust independently making the Ramp the perfect solution for uneven surfaces - Free Standing Portable Ramp Design:
- It is ideal for entryways with doors that swing both in and out - High-Strength Aluminum Materials:
- Made completely out of high-strength aluminum which will not rust or corrode over time - Height Adjustment:
- 12": 1-3/8" - 2-3/4"
- 24": 1-11/16" - 4-3/8" - Swivel feet accommodate varying heights, angles and surface types
- Made of high strength aluminium that will not rust or corrode
- Extruded, slip-resistant surface for superior traction
- 36 inches wide
- Weight Capacity is 700 lbs
- Transitions Advantage:
- Sturdy, seam-free surface makes Transitions ramp safe solution for wheelchair, scooter, walker, and cane users
- Attractive designs are available in multiple styles and materials to suit user needs and taste
- Slip-resistant tread and surfaces
- Durably designed for years of continued use
- Quick and easy setup and removal - installs in minutes so theres little-to-no disruption
- Ideal for doorways, sliding glass doors, and raised landings
- Portable, convenient, and durable
More Information
- Getting Started With the Ramp:
1. The aluminum, self-supporting ramp can be used with or without the supplied adjustable swivel feet. To protect floors, foam, rubber, or other non-abrasive, protective material may be affixed to the underside of ramp.
2. Measure the rise to determine if the adjustable swivel feet are needed.
3. Position the ramp and adjustable feet as needed to obtain correct height. Adjust feet as needed to ensure both feet are in contact with the ground. - Fastening Ramp to Landing:
The Transitions Angled Entry Ramp must be fastened to the landing before use. Use the two pre-drilled holes in the bottom of the ramp to fasten to the landing or threshold. Wood screws, sheet metal screws, or concrete bolts may be necessary, depending on the application.
1. Attaching to Wood:
- Fasten Transitions Angled Entry Ramp by installing one 1/4" x 1" self-drilling stainless steel screw (supplied) through each hole.
- Use the two pre-drilled holes in the bottom of the Transitions Angled Entry Ramp as a template to mark the positions to drill.
- Using a 1/4" masonry bit, drill two holes at the marked locations. Drill to a depth specified by the pin drive anchor manufacturer instructions.
- After drilling, make sure that the holes are free of any residue and/or debris.
- Align the Transitions Angled Entry Ramp over the drilled holes.
- Install 1/4" x 1 1/2" pin drive concrete anchors into the holes per the pin drive anchor manufacturer instructions.
- Safety And Maintenance:
- Regularly check ramp for damage and tighten any loose fasteners
- Keep ramp surface clear of ice, snow, dirt, leaves, and other debris
- For snow or ice, remove accumulation and sweep surface clean
- To remove dirt, leaves, and other debris, sweeping the surface or using a garden hose will usually suffice
- If needed, use a damp cloth or soft brush with non-alkaloid detergent and water
- Rinse well and use extra caution if ramp surface is wet - Important Information:
- Rated load is 700 pounds, 350 pounds per caster or wheel
- Never exceed rated load
- Read and follow all labels, instructions, safety and maintenance information before use
- Do not use if ramp is damaged or unstable
- For wheelchairs and scooters only (not intended for commercial use)
- Ramp may be slippery when wet or icy
- Use only if sufficient maneuvering room is available at both ends of the ramp to assure safe travel when entering and exiting the ramp
- Use ramp only with a qualified helper and always use your lap belt
Specification
Particulars TAER 12 TAER 24 Overall dimensions 12" x 36" x 1.25 24" x 36" x 2" Height (ramp only) 1-3/8" 1-11/16" Usable height w/ 1" swivel feet 1-15/16" to 2-3/4" N/A Usable height w/ 1 1/2" swivel feet N/A 2-1/8" to 3-3/8" Usable height w/ 2 1/2" swivel feet N/A 3-3/16" to 4-3/8" Weight Capacity 700 lbs., 350 lbs. per caster or wheel 700 lbs., 350 lbs. per caster or wheel Weights and dimensions are approximate and subject to change. - Extruded Tread Surface:
-
Size Chart / measuring guide
- Videos
-
Warranty Information
Lifetime Warranty If the product you received is damaged or not what you expected it to be, and want to return the item, please submit a return request to our Customer Service department via email us at contact@buildmywheelchair.com for return instructions and to receive a return authorization number. All items must be returned in their original packaging, including any documentation, and must be in new, re-sellable condition. Any custom built item that is built to special specifications is ineligible for return. This includes but is not limited too; ultra lightweight wheelchairs, heavy duty wheelchairs, tilt and space wheelchairs, pediatric wheelchairs, outdoor/all terrain power wheelchairs, power elevating/recline/tilt power wheelchairs, rehab shower commode chairs, bathroom transfer systems, standing frames and gait trainers. For hygiene reasons, all seat cushions, back cushions, positioning components and any items that have been in “skin contact” are ineligible for return. Buildmywheelchair.com must be notified within 48 hours of delivery for any damage or request for return on any product eligible for return. Once notification of return has been completed, merchandise must be returned within 30 days of the receipt of order. No returns are accepted after 30 days. Returns will be reviewed and inspected before issuing credit. A restocking fee of 30% will apply to items eligible for return and will require approval from product manufacturer before credit or reimbursement. Shipping charges will be deducted from your refund if you have us assist in return shipping. Allow 2 to 4 weeks to process the credit and it will be applied to your credit card or original method of payment.
